ISO 3382-1 PDF

ISO. First edition. Acoustics — Measurement of room .. ISO , together with ISO and ISO , cancel and replace ISO. NBR ISO Acoustics – Measurement Of Room Acoustic Parameters – Part 1: Performance Spaces. Be notified when this Standard is updated or. In this paper a selection of the most important ISO parameters is at Hz. Room acoustic parameters described in ISO where derived.

Author: Bagore Nigis
Country: Trinidad & Tobago
Language: English (Spanish)
Genre: Career
Published (Last): 24 November 2010
Pages: 189
PDF File Size: 18.62 Mb
ePub File Size: 8.64 Mb
ISBN: 943-5-95788-819-1
Downloads: 54052
Price: Free* [*Free Regsitration Required]
Uploader: Tojam

This requires a signal-to-noise level of at least 35 dB. If the measurement result is used for correction of a.

ISO 3382 2 2008

In some countries, building codes specify the required reverberation times in classrooms and other categories of room. Reverberation time in ordinary rooms 1 Scope This part of ISO specifies methods for the measurement of reverberation time in ordinary rooms.

For other reverberation time measurements, ISO covers auditoria and performance spaces, and ISO absorption coefficient 3328-1 in a reverberation room. Rooms may include domestic rooms, stairways, workshops, industrial plants, classrooms, offices, restaurants, exhibition centres, sports halls, and railway and airport terminals. The izo measuring technique is based on visual inspection of every single decay curve.

Enviado por Christiele flag Denunciar. Revision of ISO Performance rooms ISOAcoustics — Application of new measurement methods in building and room acoustics IECElectroacoustics — Octave-band and fractional-octave-band filters 3 Terms and definitions For the purposes of this document, the following terms isoo definitions apply.

However, in the vast majority of rooms, it is left to the design team to specify and design for a reverberation oso that is reasonable for the purpose of a room.


The measurement results can be used for correction of other acoustic measurements, e. First, the sound pressure level from noise sources, the intelligibility of speech, and the perception of privacy in a room are strongly dependent on reverberation time.

The introduction of the option of a survey measurement is intended to promote more frequent measurement of reverberation time in rooms where it is relevant.

It is obvious that a very simple measurement is better than no measurement.

For undated references, the latest edition of the referenced document including any amendments applies. ISO specifies three levels of measurement accuracy: For dated references, only the edition cited applies. Annex A contains some additional information about the measurement uncertainty of the reverberation time. The main difference concerns the number of measurement positions and thus the time required for the measurements. 3382-1 part of ISO is intended iiso contribute to the general understanding and acceptance of reverberation time for room quality and usability.

It describes the ido procedure, the apparatus needed, the required number of measurement positions, and the method for evaluating the data and presenting the test report.

If decay values of 5 dB to 35 dB below the initial level are used, it is labelled T Reverberation time measurements should be made in a room containing no people.

Thus, if T is derived from the time at which the decay curve first reaches 5 dB and 25 dB below the initial level, it is labelled T Second, reverberation time is measured to determine the correction term for room absorption inherent in many io measurements, such as sound insulation measurements according to ISO all parts and sound power measurements according to ISO This part of ISO does not repeat the technical details of ISO isoo, but deals with the measurement of reverberation time, only, in any kind of room.


The use of rotating microphones during the measurement of decay curves has been considered by the working group, and this procedure is found to be without a clear physical meaning and thus it is only accepted for the interrupted noise method lso only when the result is used for a correction term. With modern measuring equipment, the decay curves are normally not displayed and this may introduce a risk that abnormal decay curves are used for the 33382-1 of the reverberation time.

ISO Acoustics – Measurement of Room Acoustic Parameters. Part 1 – Google Books

It is then labelled accordingly. However, a room with up to two persons present may be allowed to represent its unoccupied state, unless otherwise specified. An alternative measurement technique, however, is to use a period of maximum-length sequence MLS type signal or other deterministic, flat-spectrum signal like a sine sweep and transform the measured response back to an impulse response.

There are several reasons to measure reverberation time. However, a preference has been given to the 20 dB evaluation range for several reasons: For this reason, Annex B introduces two new measures that quantify the degree of non-linearity and the degree of curvature of the decay curve.

Thus, this part of ISO fills a gap among measurement standards for acoustic properties of buildings. These measures may be used to give warnings when the decay curve is not linear, and consequently the result should be marked as less reliable and not having a unique reverberation.